Kenmore 60212 Owner's Manual download pdf (Page 9)

Reverse Doors (optional)

IMPORTANT: If you want to reverse your doors so that they

open in the opposite direction, follow these steps. If you are not

reversing the doors, see “Replace Doors and Hinges.”

Graphics follow these instructions.

Cabinet

1. Remove the three dome caps and the screws from handle

side and move them to opposite side. See Graphic 1-1.

2. Using the three ⁵⁄₁₆" hex-head hinge screws, removed in

Step 1, insert two screws halfway into the holes, leaving

space to insert the center hinge.

3. Once the refrigerator door is in place, slide the center hinge

from the right onto the screws, insert the third screw, and

then tighten all screws completely.

NOTE: Make sure the washers are in place on both the top

and bottom pins of the center hinge.

4. Remove cabinet hinge hole plugs from cabinet top and

move them to opposite side hinge holes as shown.

See Graphic 1-2.

Freezer Door

1. Remove the door handles. See the model specific graphics

later in these instructions.

Door Handles installed with flat-head screws and setscrews:

■ Remove the two flat-head handle screws from the

bottom of the freezer door handle.

■ Using the ¹⁄₈" hex key, loosen the setscrew attaching the

top of the handle.

■ Pull the handle away from the door to release it from the

shoulder screw. Keep all parts together.

Door handles installed with flat-head screws only:

■ Remove the screw cover and the three flat-head handle

screws. Keep all parts together.

2. Remove door hinge hole plug from freezer door. Move to

opposite side hinge hole as shown. See Graphic 3.

3. Remove the brand badge using the plastic tool (provided).

Replace it with the badge provided in the Reversibility Kit

located inside the crisper drawer. For proper placement, see

the Brand Badge Placement template (the last page of this

manual).

NOTES:

■ To avoid scratching the finish, do not use a sharp or

metallic object to pry the brand badge from the door.

■ Rub a small amount of liquid dish soap over any

adhesive residue with your fingers. Rinse the door with

warm water and dry with a soft cloth.

4. Remove door handle hole plug and discard it. See

Graphic 7. Place the new door handle hole plug (provided in

the Reversibility Kit located in the crisper drawer) into the

hole on the opposite side of the door.

5. Depending on your model, remove the shoulder screw and

its washer from the left-hand side of the door and fasten it

into the hole on the opposite side.

6. Remove door stop. Move to opposite side of refrigerator

door as shown. See Graphic 5.

7. Position freezer handle on opposite side of the freezer door

as shown. See Graphic 2. First, drive the bottom two screws

into handle. Align upper portion of handle and drive top

screw into handle. Depending on your model, place the

handle on the shoulder screw and push the handle toward

the door until the mounting base is flush against the door.

8. Tighten all screws. Set aside door until hinges and

refrigerator compartment door are in place.

9. Depending on your model, replace screw cover. See

Graphic 2.

A. ⁵⁄₁₆" Hex-head hinge screws

B. Washers

Door Hinge

Hole Plug

Cabinet Hinge

Hole Plug

Dome Cap

Washer

Setscrew

Shoulder

Screw

Shoulder

Screw Washer

Door Stop

Screw

Flat-Head

Handle

Screw

Door Handle

Hole Plug

1 2 3 4 5 6 7 8 9 10 11 12 13 14 ... 63 64

Comments to this Manuals

No comments

Kenmore 60212 Owner's Manual Page 9

Comments to this Manuals

Related products and manuals for Fridges Kenmore 60212