Kenmore 60212 Owner's Manual download pdf (Page 10)

Refrigerator Door

1. Remove the door handles. See the model specific graphics

later in these instructions.

Door Handles installed with flat-head screws and setscrews:

■ Remove the screws from the top of the refrigerator door

handle.

■ Remove the setscrew from the lower part of the handle.

■ Pull the handle away from the door to release it from the

shoulder screw. Keep all parts together.

Door handles installed with flat-head screws only:

■ Remove the screw cover, and the three flat-head handle

screws. Keep all parts together.

2. Remove door hinge hole plug from refrigerator door. Move

to opposite side hinge hole as shown. See Graphic 3.

3. Remove door handle sealing screws. Move to opposite side

of refrigerator door as shown. See Graphic 4.

4. Remove door handle hole plug and discard it. See Graphic

7. Replace on opposite side with the door handle hole plug

provided in the Reversibility Kit located in the crisper.

5. Remove door stop. Move to opposite side of refrigerator

door as shown, making sure that the hole in the door stop

plate is aligned perfectly with the hole for the Bottom Hinge

pin. See Graphic 5.

6. Position refrigerator handle on opposite side of the

refrigerator door as shown. See Graphic 6. First, drive top

two screws in handle, and then align lower portion of handle

and drive bottom screw into handle. Depending on your

model, place the handle on the shoulder screw and push the

handle toward the door until the mounting base is flush

against the door.

7. Tighten all screws. Set aside refrigerator door until bottom

hinge is installed on refrigerator.

8. Depending on your model, replace screw cover. See

Graphic 6.

Replace Doors and Hinges

NOTE: Graphic may be reversed if door swing is reversed.

1. Replace the parts for the bottom hinge as shown. Tighten

screws. Replace the refrigerator door.

NOTE: Provide additional support for the doors while the

hinges are being moved. Do not depend on the door

magnets to hold the doors in place while you are working.

2. Measure the distance from the bottom of the refrigerator

door to the floor. The distance should be approximately 3¹⁄₂"

(88 mm).

NOTE: If necessary, loosen the bottom hinge, without

removing the screws, adjust the door to the correct height

and fully tighten the screws.

3. Assemble the parts for the center hinge as shown and

tighten all screws. See Center Hinge graphic. Replace the

freezer door.

4. Assemble the parts for the top hinge as shown. See Top

Hinge graphic. Do not tighten screws completely.

5. Line up the doors so that the bottom of the freezer door

aligns evenly with the top of the refrigerator door. Tighten

all screws.

NOTE: The distance between the doors should be

approximately ⁵⁄₈" (16 mm).

Final Steps

1. Check all holes to make sure that hole plugs and screws are

in place. Reinstall top hinge cover. See Top Hinge graphic.

2. Remove the cover from the base grille. Move the cover to

the opposite side.

3. Align the clips on the base grille with the screws on the

bottom of the cabinet. Push the base grille toward the

cabinet until it is flush.

4. Plug into a grounded 3 prong outlet.

5. Reset the controls. See “Using the Control(s).”

6. Return all removable door parts to doors and food to

refrigerator.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 ... 63 64

Comments to this Manuals

No comments

Kenmore 60212 Owner's Manual Page 10

Comments to this Manuals

Related products and manuals for Fridges Kenmore 60212