Kenmore 59921 Installation Guide Page 11
- Page / 24
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
11
WarrantySafety CleaningOperation
Installation
Service Parts
Note: Purchase Non-Duct Kit,
Kenmore part number 59921.
1. CAUTION: Use only expandable
aluminum duct provided with non-duct
kit.
2. Do not remove the protective plastic
film covering the decorative flue at this
time.
3. Remove damper flaps from
damper/duct connector and
discard flaps.
4. Attach non-duct collar to non-duct
plenum using (4) #8 x 3/8” pan
head screws.
5. Measure distance “A”. Cut a length
offlexiblemetalduct(extended)to
this dimension.
6. Attach aluminum flexible duct to
the damper / duct connector with
a tie wrap.
7. Attach flexible duct to non-duct
plenum collar and secure with tie
wrap. Tape all joints with duct tape.
8. Remove protective plastic film
covering the lower flue only.
9. Carefully place both flues into the
recessed area of hood top.
10. Attach non-duct plenum with collar
to upperflue using (4) #8 x 3/8”
pan head screws.
11. Hold hood up close to wall mounting
location and plug power cord into
wall outlet.
12. Align the hood and center it above
the hood mounting bracket. Gently
lower the hood until it securely
engages the bracket.
13. If a framing
member is
not present:
With the
hood hanging
in place, drill
through both
holes located
in the inside
lower back
of hood using
a
5
⁄ 16”drill
bit. Insert
the included
drywall
anchors into
thedrilledholes(oneforeachhole).
14. Install(2)washersand(2)#8x1-1/2”mountingscrews
through the back of the hood and into the drywall
anchors. Verify that the hood is centered and leveled.
Tighten all screws completely.
A
NON-DUCT PLENUM
6” ALUMINUM
FLEX DUCT
DAMPER / DUCT
CONNECTOR
4-7/8”
NON-DUCT COLLAR
15. Slide up the upper flue
until it is aligned with its
mounting bracket. The
bracket should be inside the
flue. Secure the upper flue
on the upper flue mounting
bracketusing(2)#8x 3/8”
mounting screws.
16. Remove protective plastic
film covering the flue and
the hood.
INSTALL THE HOOD (NON-DUCTED HOODS ONLY)
HOLE LOCATIONS
Ø5/16”
TYP.
MOTOR/
BLOWER
ASSEMBLY
SIDE VIEW
INSIDE
BACK
OF
HOOD
UPPER
FLUE
UPPER FLUE MOUNTING
BRACKET - FRONT VIEW
METAL
LATCH
GREASE FILTER
NON-DUCT
RECIRCULATION
FILTER
NON-DUCT
FILTER
MOUNTING
TABS
17. Install the non-duct recirculation filter as shown. Turn
mounting tabs on hood to secure filter.
18. Reinstall grease filter by aligning rear filter tabs with slots
in the hood. Push in the metal latch tab, push filter into
position and release. Make sure filter is securely engaged
after installation.
- Range Hood 1
- FOR DOMESTIC COOKING ONLY 2
- OPERATION 3
- KENMORE LIMITED WARRANTY 3
- LIGHT BULBS 3
- TOOLS NEEDED FOR INSTALLATION 4
- PARTS NOT INCLUDED WITH HOOD* 4
- CLEANING 4
- PARTS INCLUDED WITH HOOD 4
- EQUIVALENT DUCT LENGTH CHART 5
- INSTALL THE DUCTWORK 6
- INSTALL MOUNTING BRACKET 6
- INSTALL THE WIRING 7
- INSTALL CURVED GLASS PLATE 8
- INSTALL BULBS 8
- INSTALL DUCT CONNECTOR 8
- 6” ROUND 10
- (VERTICAL 10
- DUCTING) 10
- Installation 11
- SERVICE PARTS 12
- INSTRUCCIONES DE SEGURIDAD 13
- BOMBILLAS 14
- FUNCIONAMIENTO 14
- GARANTÍA LIMITADA DE KENMORE 14
- HERRAMIENTAS NECESARIAS PARA 15
- LA INSTALACIÓN 15
- LIMPIEZA 15
- 2 pulg 17
- 16 pulg 17
- INSTALE LAS BOMBILLAS 19
- 4 M\, PULG 22
- (12.3 cm) 22
- PIEZAS DE SERVICIO 23
Related products and manuals for Cooker hoods Kenmore 59921
Cooker hoods Kenmore 51392 Owner's Manual
(32 pages)
(32 pages)
Cooker hoods Kenmore 51289 Owner's Manual
(32 pages)
(32 pages)
Cooker hoods Kenmore 51263 Owner's Manual
(32 pages)
(32 pages)
Sandpiper Pumpen Benutzerhandbücher
Beginnend mit H
Comments to this Manuals