Kenmore 75232 Installation Guide Page 5
- Page / 68
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
5
Parts supplied (all models):
Tools needed for gas installations:
8" (203 mm) or 10"
(254 mm) pipe wrench
8" (203 mm) or 10"
(254 mm) adjustable wrench
(for gas connections)
Pipe-joint compound
resistant to propane gas
Leveling legs (4)
(Length and appearance of legs may vary according to model.)
“Y” connector
Short inlet hose
Inlet hose
Rubber washer
Parts needed (steam models):
Parts package is located in dryer drum. Check that all parts
are included.
If using a power supply cord:
Use a UL Listed power supply cord kit marked for use with clothes
dryers. The kit should contain:
■ A UL Listed 30-amp power supply cord, rated 120/240 volt
minimum, and have a temperature rating of 140ºF (60ºC)
minimum. The cord should be type SRD or SRDT and be at least
4 ft. (1.22 m) long. The wires that connect to the dryer must end
in ring terminals or spade terminals with upturned ends.
■ A UL Listed strain relief.
Parts needed: (Not supplied with dryer)
Check local codes. Check existing electrical supply and venting.
See “Electrical Requirements” and “Venting Requirements” before
purchasing parts.
Mobile home installations require metal exhaust system hardware
available for purchase from the dealer from whom you purchased
your dryer. For further information, call 1-844-553-6667 (U.S.) or
1-800-469-4663 (Canada).
Optional Equipment: (Not supplied with dryer)
Refer to your Use and Care Guide for information about accessories
available for your dryer.
LOCATION REQUIREMENTS
You will need:
■ A location allowing for proper exhaust installation. See
“Venting Requirements.”
■ A separate 15- or 20-amp circuit needed for gas dryers and
30-amp circuit needed for electric dryers.
■ If using power supply cord, a grounded electrical outlet located
within 2 ft. (610 mm) of either side of dryer. See “Electrical
Requirements.”
■ Floor must support dryer weight of 200 lbs. (90.7 kg). Also
consider weight of companion appliance.
■ Level oor with maximum slope of 1" (25 mm) under entire
dryer. If slope is greater than 1" (25 mm), clothes may not
tumble properly and automatic sensor cycles may not operate
correctly.
■ For garage installation, place dryer at least 18" (460 mm)
above oor.
■ Steam models only: Cold water faucet located within
4 ft. (1.2 m) of the water ll valves, and water pressure of
20-100 psi (137.9-689.6 kPa). You may use your washer’s
water supply by purchasing the necessary parts noted in
“Parts needed.”
■ If you live in a hard water area, use of a water softener is
recommended to control the buildup of scale through the
water system in the dryer. Over time, the buildup of lime
scale may clog dierent parts of the water system, which
will reduce product performance. Excessive scale buildup
may lead to the need for certain part replacement or repair.
IMPORTANT: Do not operate, install, or store dryer where it will
be exposed to water, weather, or at temperatures below 45°F
(7°C). Lower temperatures may cause dryer not to shut o at
end of automatic sensor cycles, resulting in longer drying times.
NOTE: No other fuel-burning appliance can be installed in the
same closet as a dryer.
or
- Kenmore® 1
- DRYER SAFETY 2
- INSTALLATION REQUIREMENTS 4
- LOCATION REQUIREMENTS 5
- Steam Non-Steam 6
- ELECTRICAL REQUIREMENTS – 7
- U.S.A. ONLY (SPÉCIFICATIONS 7
- ÉLECTRIQUES – ÉTATS-UNIS 7
- SEULEMENT) 7
- ELECTRIC DRYER POWER 8
- HOOKUP – CANADA ONLY 8
- GAS DRYER POWER HOOKUP – 8
- INSTALL LEVELING LEGS 9
- 2. Screw in leveling legs 10
- POWER SUPPLY CORD CONNECTION 11
- 3. Connect ground wire 12
- 1. Remove center screw 12
- 4. Connect remaining wires 12
- 3. Connect remaining wires 13
- 2. Connect neutral wire 13
- 4. Connect ground wire 14
- 1" 15
- 3½" 15
- MAKE GAS CONNECTION – 16
- U.S.A. AND CANADA 16
- Venting Requirements 17
- Plan Vent System 18
- CONNECT INLET HOSES 19
- 7. Check for leaks 20
- 6. Turn on cold water faucet 20
- 1. Level dryer 21
- 2. Adjust leveling legs 21
- REVERSE DOOR SWING (OPTIONAL) 22
- 7. Rotate outer door 23
- 8. Flip door over 23
- 9. Attach door hinges 23
- 10. Remove door strike and 23
- TROUBLESHOOTING 24
- SEGURIDAD DE LA SECADORA 25
- ADVERTENCIA 25
- ADVERTENCIA: 26
- REQUISITOS DE INSTALACIÓN 27
- REQUISITOS DE UBICACIÓN 28
- DIMENSIONES DE LA SECADORA 29
- REQUISITOS ELÉCTRICOS – 30
- EE.UU. SOLAMENTE 30
- CONEXIÓN ELÉCTRICA 31
- DE LA SECADORA A GAS – 31
- EE.UU. Y CANADÁ 31
- INSTALACIÓN DE LAS PATAS 33
- NIVELADORAS 33
- PARA HACER LA CONEXIÓN 34
- ELÉCTRICA – EE.UU. SOLAMENTE 34
- 3. Conecte el hilo a tierra 35
- 1. Quite el tornillo central 36
- 2. Conecte el hilo neutro 36
- CONEXIÓN POR CABLE DIRECTO 37
- 3. Abra la válvula de cierre 40
- CONEXIÓN DE LAS MANGUERAS 42
- DE ENTRADA 42
- (101 mm) 43
- /4" 43
- (768 mm) 43
- 1. Nivele la secadora 44
- LISTA DE CONTROL DE LA 45
- INSTALACIÓN TERMINADA 45
- DE LA PUERTA (OPCIONAL) 46
- 7. Gire la puerta exterior 47
- 8. Dé vuelta la puerta 47
- SOLUCIÓN DE PROBLEMAS 48
- SÉCURITÉ DE LA SÉCHEUSE 49
- EXIGENCES D’INSTALLATION 51
- EXIGENCES D’EMPLACEMENT 52
- DIMENSIONS DE LA SÉCHEUSE 53
- POUR L’INSTALLATION 53
- RACCORDEMENT DE LA SÉCHEUSE 54
- AVERTISSEMENT : 55
- 2. Planier la connexion 57
- L’ÉVACUATION 58
- Brides de serrage : 59
- RACCORDEMENT DES 60
- TUYAUX D’ALIMENTATION 60
- 3. Serrer les raccords 61
- 7. Recherche de fuites 61
- ÉTABLIR L’APLOMB 62
- DE LA SÉCHEUSE 62
- RACCORDEMENT DU SYSTÈME 62
- D’ÉVACUATION 62
- ACHEVER L’INSTALLATION LISTE 63
- DE VÉRIFICATION 63
- INVERSION DU SENS D’OUVERTURE 64
- DE LA PORTE (FACULTATIF) 64
- 8. Retourner la porte 65
- 13. Contrôler l’alignement 66
- Kenmore ® 68
Related products and manuals for Electric laundry dryers Kenmore 75232
(40 pages)© 2020, manymanuals.com. All rights reserved. | 0.715 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals