Kenmore 141.173373 User Manual download pdf (Page 13)

Assembly Instructions

CAUTION: While it is possible for one person to

assembie this grill, obtain assistance from another

person when handling some of the larger, heavier

pieces, especially the grill head.

Figure 1

During unpacking and assembly always wear work

oves and eye protection.

glo . ,

2. Open Lid of shipping carton and remove top sheet

of cardboard. Lay cardboard sheet on floor and

use as a work surface to protect floor and grill parts

from scratches.

3. Slice ail carton corners with a sharp utility knife to

lay open the carton panels.

4. Remove all packing materials and parts boxes

flanking or resting on grill head.

5. Remove all components packed inside grill head.

6. With an assistant, lift the grill head away from the

shipping carton and place it on the cardboard work

surface. Be careful not to set grill head down on

flexible metal hose of the pre-assembled valve kit

or you may damage the hose.

7. Use the parts list to check that all parts have been

included.

8. Inspect the grill for damage as you assemble.

Do not assemble or operate the griil if it appears

damaged. If there are damaged or missing parts

when you unpack the shipping box. or if you have

questions during the assembly process, call:

1-888-317-7642 8am-8pm CST, Mon-Fri

Q Assembling The Grill Cart

NOTE: To aid in assembly, compare hardware to

diagrams on page 7 and page 9.

1. Before attaching the Cart Bottom Shelf to the

Cart Legs be sure the holes for the Door Stop

on Cart Bottom Shelf are located on the front

side. Be sure the Cart Leg Brackets and air

vents all face outward. Rimt Cart Leg Bracket

has a semi-circle cutout at top front.

See Figure 1.

Install the Cart Bottom Shelf between the Cart

Legs. Align the holes on Cart Legs with the

threaded holes at the corners of Cart Bottom

Shelf. Tighten securely using 8 of the 1/4"x2"

Pattern Head Screws provided. See Figure 1.

Screw the 2 Casters into the Caster Seats (see

bottom of Cart Legs). Turn the threaded Caster

Stem by hand, clockwise until it stops. Tighten

securely using the Customized Wrench provided.

See Figure 1.

Install the 2 Wheels to the Right Cart Legs, b'

inserting the Wheel Bolt through the Wheel anc

axle hdie on the Cart Leg as showt in

Put spring washer and 3/8" nut onto

.....................

tighten securely using the Customized Wrench

provided. Do not overtighten or \Aheel will not

turn freely. Snap Wheel Hub Caps onto Wheels.

Figure

bolt and

5. For LP Gas grills:

Place the Tank Pull-out Trw Assembly on the Cart

Bottom Shelf. Extend the Tank Tray outward from

the Bracket so you can align the holes on the

Bracket with the threaded holes on the top of Cart

Bottom Shelf. Tighten securely using 4 of the 1/4"x1/

2" Pattern Head Screws provided. See Figure 2.

6 Install the Cart Rear Panel to inside of rear Cart

Legs making sure that air vents face outward.

Align the holes on the Cart Rear Panel with the

threaded holes on rear Cart Legs. Tighten

securely using 4 of the 1/4"x1/2" Pattern Head

Screws provided. See Figure 3.

CART LEG

Figure 2 (LP gas model only)

LEFT CART LEG

Figure 3

1 2 ... 8 9 10 11 12 13 14 15 16 17 18 ... 42 43

Comments to this Manuals

No comments

Kenmore 141.173373 User Manual Page 13

Comments to this Manuals

Related products and manuals for Grills Kenmore 141.173373