f J J J J ,i J J J J J ,i J J
IJ..IJ J J J J. .1J J J J J J
SECTION 2
,i J ,j J J J ,i J J J J J ,i J J
JJ JJJJ JJJJ J
J J. J J J J J J, J J J J J J J
HOW YOUR WATER SOFTENER WORKS
ij.jjjjjj.jjjjjj.jjjj
IJJJJJJJJJJJJJJJJJ
IJJJ^J^JJJJJJJJJJ
rjjJjjÆjjjjj^jjjjj
ijjjj^majjjjjjjjjj
J JJJ^J J J
IJJJJJJJJJJJJJJJJJ
rjJJJJJ^JJJJJJ^JJJJJ
IJJJJJJJJJJJJJJJJJ
^ EXTRA RECHARGE
Sometimes, a manually started
regeneration (recharge) may be
desired, or needed. Two exam
ples are:
- You have used more water than
usual (guests visiting) and you
may run out of soft water before
the next timer started regenera
tion.
- You did not refill the softener
with salt before it was gone. After
you refill with salt:
You can start a regeneration right
away, or you can set the timer to
regenerate at the next 2:00 AM (or
other preset recharge time). Do
the following.
^ RECHARGE NOW
M l( h
I’UO
RECHARGE
Press the ON/OFF-HOLD but
ton and hold until ^RECHARGE,
Serv and Fill begin to flash in the display. Upon
reaching fill, the first cycle of regeneration, the flash
ing Serv goes off and Fill is on steady. RECHARGE
continues to flash. This regeneration will last for
about 2 hours. After the 2 hours, you will have soft
water again.
“^Note:
If the CLEAN feature is set to ON, a cleaning back
wash {CLEAN and Bkzvsh or Rinse flashes in the dis
play, along with the minutes of the dean cycle re
maining) precedes the recharge.
^ RECHARGE TONIGHT
~i,nn
MIJO
RECHARGE TONtGHl
WATER FLOW
Press and release (do not hold) the
ON / OFF-HOLD button. RE
CHARGE TONIGHT flashes in the display, and the
softener begins regeneration at the next preset re
charge time. Press and release the ON/ OFF-HOLD
button once more if you dedde to cancel the regen
eration, and RECHARGE TONIGHT.
^ SALT MONITOR SYSTEM
The face plate timer has a low salt monitor with an
indicator light to remind you to refill the storage
tank with salt. To set this monitor system:
Lift the salt hole cover and level the salt in the
storage tank.
The salt level decal, on the brinewell inside the
tank, has numbers from 0 to 8 (see drawing be
low). Observe the number the leveled salt is at
or closest to.
Now, press the SALT LEVEL ADJUST button
until black bars display up to the salt level num
ber. For example, the pictures below show the
salt level at 6.
Finally, set the level you want the low salt indi
cator light to come on. Press the SIGNAL LIGHT
ADJUST button until a (^) shows opposite this
number. In the example below, the light will
come on when the stored salt drops to level 2. At
level 2, the storage tank is about 1 / 3 full. This is
the lowest you should allow the stored salt level
to drop to (see note on page 1-6).
If you wish to turn the salt monitor off, press the
SIGNAL LIGHT ADJUST button until OFF
shows above.
Note:
For accurate salt monitor operation, always use
nugget or pellet water softener salt. See page 1-6.
2 - 1
(40 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals