Kenmore ULTRASOFT 280 User Manual download pdf (Page 10)

SECTION 2 HOW YOUR WATER SOFTENER WORKS

yy TIMER FEyXTURES

ij^jjjjj^jjjjj^jjj

IJ^J J JJJ^J J J

j jjj^j j j

rj:.f

ij^j^iPCi^j j jjj^j j j

ij^ j jjj^j j j

ij^jjjjj^jjjjj^jjj

>j^j.ij.ij^j.ij.ij^j.ij

^ EXTRA RECHARGE

Sometimes, a manually started

regeneration (recharge) may be

desired, or needed. Two exam

ples are:

- You have used more water than

usual (guests visiting) and you

may run out of soft water before

the next timer started regenera

tion.

- You did not refill the softener

with salt before it was gone. After

you refill with salt:

You can start a regeneration right

away, or you can set the timer to

regenerate at the next 2:00 AM (or

other preset recharge time). Do

the following.

^ RECHARGE NOW

M II If

I'LIIJ

RECHARGE

WATER FLOW

Press the RECHARGE button

and hold unfA ^RECHARGE, Serv

and Fill begin to flash in the display. Upon reaching

fill, the first cycle of regeneration, the flashing Serv

goes off and Fill is on steady. RECHARGE continues

to flash. This regeneration will last for about 2

hours. After the 2 hours, you will have soft water

again.

’^'Note:

If the CLEAN feature is set to ON, a cleaning back

wash {CLEAN and Bkwsh or Rinse flashes in the dis

play, along with the minutes of the dean cycle re

maining) precedes the recharge.

I'IJO

RECHARGE TONIGHT

WATER FLOW

^ RECHARGE TONIGHT

Press and release (do not hold) the

RECHARGE button. RE

CHARGE TONIGHT flashes in the display, and the

softener begins regeneration at the next preset re

charge time. Press and release the RECHARGE but

ton once more if you decide to cancel the regenera

tion, and RECHARGE TONIGHT will not flash in

the display.

^ SALT MONITOR SYSTEM

The face plate timer has a low salt monitor with an

indicator light to remind you to add salt to the stor

age tank. To set this monitor system:

Lift the salt hole cover and level the salt in the

storage tank.

The salt level decal, on the brinewell inside the

tank, has numbers from 0 to 8 (see drawing be

low). Observe the number the leveled salt is at

or closest to.

Now, press the SALT LEVEL ADJUST button

until black bars display up to the salt level num

ber. For example, the pictures below show the

salt level at 6.

Finally, set the level you want the low salt indi

cator light to come on. Press the SIGNAL LIGHT

ADJUST button until a (★ ) shows opposite this

number. In the example below, the light will

come on when the stored salt drops to level 2. At

level 2, the storage tank is about 1/3 full. This is

the lowest you should allow the stored salt level

to drop to (see note on page 1-6).

If you wish to turn the salt monitor off, press the

SIGNAL LIGHT ADJUST button until OFF

shows above.

Note:

Your salt monitor is an estimate of your salt level; ac

curacy depends on the type of salt used and other

regeneration characteristics.

2 - 1

Problems, Questions? Call 1-800-426-9345 Kenmore Water Line

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 ... 35 36

Comments to this Manuals

No comments

Kenmore ULTRASOFT 280 User Manual Page 10

Comments to this Manuals

Related products and manuals for Water equipment Kenmore ULTRASOFT 280