Kenmore Washer User Manual download pdf (Page 15)

Auto Temp Control

АТС {Auto Temp Control) electronically senses and maintains a

uniform water temperature. АТС regulates incoming hot and cold

water. The АТС is automatically turned On when a cycle is

selected. (See "Preset Cycle Settings” in “Cycles.”)

АТС is available with WARM/WARM, WARM/COLD and COLD/

COLD settings. The AUTO TEMP CONTROL light will glow

indicating that АТС is working.

_ Auto Temp

CONTHOL

• HOT/COLO

• WARM/WARM

• Warm / Cold

• COLD/COLD

• TAP COLD/COLD

Wash/Rinse

TEMP

■ АТС ensures consistent cleaning.

■ When using АТС, warm water is added to the washer to

maintain a termperature of approximately 75°F (24°C), so

detergents dissolve properly.

■ Warm washes are regulated at approximately 100°F (38°C).

■ Warm rinses are regulated at approximately 75“F (24°C). This

is a cooler warm rinse than you are used to, but it saves

energy and gives proper rinsing. The load is a comfortable

temperature to remove from the washer

Wash Time

Wash Time is preset for each wash cycle, (See “Preset Cycle

Settings” in “Cycles.”) As you press WASH TIME pad, the cycle

time (minutes) will increase or decrease in the ESTIMATED TIME

REMAINING display and a different WASH TIME light will glow. To

get the minimum wash time, press the pad until the indicator light

next to MINIMUM illuminates. This is the shortest wash time

available for that cycle.

•

• Maximum

4. Press SET DELAY TIME. 1H (one hour) will be displayed in the

time display window. The indicator light for DELAY TIME will

glow.

. Di lAr TIMF'

УЧ

SETttLAY

TIME

For a longer delay time, press SET DELAY TIME. The time will

increase by one^hour steps.

Press START. The countdown to the wash cycle will show in

the time display window.

To change the Delay Time:

■ Press STOP/CANCEL.

■ Reset the SET DELAY TIME.

■ Press START to begin the countdown.

To cancel Delay Start:

Press START again to begin the cycle right away or press

STOP/CANCEL twice.

Adjustable End Of Cycle Signal

A tone will sound at the end of the cycle. The sound level of this

tone can be adjusted by pressing END OF CYCLE SIGNAL. The

volume of tone you will hear at the end of the cycle will sound as

the pads are pressed.

• HIGH

• Low

• OFF

End of Cycle

SIGNAL

* NORMAL

»Minimum

Wash Time

When a wash cycle is started, the estimated time remaining for

the cycle, including fills and drains, will be displayed. The time

will count down to the end of the cycle. The ESTIMATED TIME

REMAINING light will glow.

> EbTiMAIKli TiNCi

RtVlAINlj'JG

Set Delay Time

You can use the SET DELAY TIME feature to delay the start of a

wash cycle for up to 11 hours (depending on you model).

1, Load the washer and fill the dispensers.

2, Close the washer lid.

3, Select the desired Cycle, Options and Modifiers.

Indicator Lights

Select Cycle

Located next to each pad, these lights show the cycle you have

selected.

Options

These lights show the Prewash and/or Rinse/Spin Options you

have selected.

Modifiers

These lights show the selected Wash/Rinse Temperature, Wash

Time, Estimated Time Remaining in cycle, and End of Cycle

Signal.

Washer Status

These lights show what portion of the cycle the washer is

operating.

Washfr Status

• W'ASHiNl.i

• Rinsing

• Auk,’ Fluff

• Ck/ihls Cifan

1 2 ... 10 11 12 13 14 15 16 17 18 19 20 21 22 23

Comments to this Manuals

No comments

Kenmore Washer User Manual Page 15

Comments to this Manuals

Related products and manuals for Washers Kenmore Washer