Kenmore 51289 Owner's Manual Page 5
- Page / 32
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
5
PARTS INCLUDED WITH HOOD
TOOLS NEEDED FOR HOOD INSTALLATION
Micromesh Grease Filters
(2 per hood)
Parts Bag
(4 no. 8-18 x 1/2" metal screws,
6 no. 8 x 5/8" round head wood screws,
6 no. 8 x 1/2" countersunk wood screws,
1 suction cup tool)
Screwdriver
(Flat & Phillips no. 2)
Pencil
Tape
Measure
Drill
(with 1/8" and
7/64" drill bits,
and 1½" hole saw)
Sabre Saw
Keyhole
Saw
-or-
Metal Foil
Duct Tape
Wire
Stripper
PARTS NOT INCLUDED WITH HOOD
OPTIONAL PARTS (purchase separately)
Non-Ducted Recirculation Filters
(Non-ducted hoods only)
(2 per hood)
Part Nos.:
S97020466 (30-in. width hoods)
S97020467 (36-in. width hoods)
7-inch Round Damper
(For use with 7-inch Round Duct)
Part No. 59183
3¼” x 10”
Damper / Duct
Connector
C
L
AB
Apoyar este borde contra la pared de atrásPlace this edge against back wall
VERTICAL EXHAUST
S
A
A
V
RTICAL EX
= 3¼” x 10”
= 3¼” x 14”
RECTANGULAR DUCTING7” ROUND DUCTING
OR
Use this template for marking; do not attempt to cut out the ducting hole through it.
NOTE: These cutouts are clearance holes; they do not need to be the exact size of ducting.
= 3¼ po x 10 po
= 3¼ po x 14 po
CONDUIT RECTANGULAIRECONDUIT ROND DE 7 PO
OU
= 3¼ pulg. x 10 pulg.
= 3¼ pulg. x 14 pulg.
CONDUCTO RECTANGULARCONDUCTO REDONDO
DE
7 PULG.
O
Appuyer ce bord au mur arrière
Utiliser ce gabarit pour marquer vos repères; ne pas tenter de découper
le trou pour le conduit à travers le gabarit.
NOTE : Les découpes incluent le jeu nécessaire à l’installation; elles ne doivent pas
être du format exact des conduits.
Use esta plantilla para crear marcados; no trate de cortar el
agujero del conducto a través de la plantilla.
NOTA: To be translated in Spanish.
MARK WHERE INDICATED
FOR THE APPROPRIATE SIZE DUCT OPENING
MARQUER LES REPÈRES AUX ENDROITS INDIQUÉS SELON
LE FORMAT DE CONDUIT UTILISÉ
TITLE TO BE TRANSLATED IN SPANIS H
Electrical access hole center
A = single blower hood
B = double blower hood
Centre du trou pour fil
d’alimentation électrique
A = hotte ventilateur simple
B = hotte ventilateur double
To be translated in Spanish
Electrical access hole center
A = single blower hood
B = double blower hood
4¼”
10½”
14½”
8”
7½”
C
C
C
Bend template along graduated
scale when installing to framed
cabinet.
Pour une installation sous une
armoire à fond en retrait, utiliser les
lignes pour mesurer l’épaisseur du
décalage causé par le mur de
l’armoire et plier le gabarit en
conséquence.
To be translated in Spanish.
EZ-1 One person Installation Kit
(including template for
ducting, printed both sides,
and installation brackets)
7” Round
Duct Connector
Long Nose
Pliers
HR0064
Sheet Metal
Shears
Shielded Halogen Bulbs
(120 V, 50 W max., MR16 or
PAR16 with GU10 base)
(2 per hood)
“Parts Not Included With Hood” available by calling
1-844-553-6667
- Range Hood 1
- TABLE OF CONTENTS 2
- KENMORE LIMITED WARRANTY 2
- SAFETY INSTRUCTIONS 3
- CLEANINGOPERATION 4
- PARTS INCLUDED WITH HOOD 5
- PARTS NOT INCLUDED WITH HOOD 5
- EQUIVALENT DUCT LENGTH CHART 6
- PREPARE THE HOOD 7
- NON-DUCTED INSTALLATIONS ONLY 8
- PREPARE THE HOOD LOCATION 10
- DUCTED INSTALLATIONS ONLY 12
- CONNECT THE WIRING 14
- INSTALL THE FILTERS 15
- INSTALL THE LIGHT BULBS 15
- SERVICE PARTS 16
- TABLA DE CONTENIDO 17
- GARANTÍA LIMITADA DE KENMORE 17
- INSTRUCCIONES DE SEGURIDAD 18
- LIMPIEZAOPERACIÓN 19
- PREPARE LA CAMPANA 22
- HORIZONTAL EXHAUST 25
- ORNILLOS 27
- PARA MADERA 27
- PARA METAL 27
- 16" 28
- CONECTE EL CABLEADO 29
- INSTALE LOS FILTROS 30
- INSTALE LAS BOMBILLAS 30
- PIEZAS DE SERVICIO 31
- Kenmore ® 32
Related products and manuals for Cooker hoods Kenmore 51289
Cooker hoods Kenmore 51263 Owner's Manual
(32 pages)
(32 pages)
Comments to this Manuals